Connect with us

Tech

Complete Steps for Linksys Router Setup and Troubleshooting

Published

on

If you are looking for a solution to cope up with slow WiFi, then performing Linksys router setup will surely be the best for you. Setting up a Linksys router will not just provide you an uninterrupted speed of the internet but also expand the coverage of your WiFi network all over your house. In addition to that, you can connect as many devices as you want with your Linksys router without signal drop.

Step-by-Step Instructions to Perform Linksys Router Setup

Given-below are the step-by-step instructions that you need to follow in order to set up your Linksys router without any ado.

  • Right off the bat, place your Linksys router in the same room as that of your modem.
  • Then, attach the antenna on your Linksys router (if any) and power it on.
  • But, before you power on your Linksys router, make sure that it is properly plugged into a working wall socket.
  • Wait for the LEDs on your Linksys router to become stable and green.
  • Connect your Linksys router to the modem using an Ethernet cable or wire.
  • Take one end of the Ethernet cable and plug it into the internet or WAN port on the rear port of your Linksys router.
  • Then, take other end of the Ethernet cable and plug it into the Ethernet or LAN port on the rear port of your modem.
  • Open an internet browser on your computer or laptop and in the address bar type 192.168.1.1 and then press the Enter keyboard.
  • You will be prompted to log in to your Linksys router.
  • Enter the default routerlogin credentials and click on the Log In button.
  • Follow the given instructions to configure your Linksys router like a pro.

Stuck With Linksys Router Setup? Try This Out!

On the off chance if you stuck at any Linksys router setup step, then without much delay, try a few troubleshooting tips highlighted below:

  • Make sure that your Linksys router is placed in close proximity with your modem.
  • Also, ensure that your Linksys router is placed openly in a center location of your home.
  • Be extremely careful with the placement as your Linksys router shouldn’t be placed inside a cabinet, under a table, in a corner, and near to walls and windows.
  • Be sure that the Ethernet cable you have used to connect your Linksys router and modem is not worn out. You can also connect your Linksys router with your modem in a wireless manner. Ask us how to do so.
  • Update the firmware of your Linksys router.
  • Ensure that the power LED on your Linksys router is green and stable before proceeding with the setup process.
  • Make sure to enter the correct routerlogin details.
  • If you are facing issues with your internet connection, power cycle your Linksys router along with your modem.
  • Make sure to attach the antenna of your Linksys router in straight upward position.

Still facing issues with Linksys router setup process? Are you unable to make the most out of your internet connection after Linksys router setup? If so, then reset your Linksys router. Sometimes, resetting your Linksys router to its default values can help you get rid of setup and internet connectivity issues.

To reset Linksys router:

  • Power on your Linksys router and disconnect it from your modem.
  • Then, locate the reset hole on your Linksys router and push it using a paper clip.
  • Hold the Linksys router reset hole for a few seconds and release it.
  • Thus, your Linksys router resets successfully.

Now, you have to configure it again using the default Linksys router login details and the instructions given-above.

Endnote

In the event that you got stuck at any Linksys router setup step, feel free to reach out to our experts via comments.

Continue Reading
Click to comment

Leave a Reply

Your email address will not be published. Required fields are marked *

Tech

How Do I Change the Password of My Netgear WiFi Router?

Published

on

By

Netgear introduces millions of WiFi devices every year and each device comes with a default password and username. Do you even know what this means? This means that the credentials of your Netgear WiFi router can be known by anyone.

In other words, if an unauthorized user gains knowledge of your default password, your WiFi router won’t be secure anymore. Your personal information won’t take seconds to get hacked! In order to ensure that you don’t get caught in this web, it is important that you change the password of your WiFi device.

For those of you who are wondering how to do that, simply access the www.routerlogin.net web page, go to the Setting option, and change the password of your Netgear WiFi router. For a more detailed process, scroll down and read on.

Guidelines to Change the Password of Your Netgear Router

Outlined below are the steps that you need to follow in order to change the password of your device:

  • Grab a power cable and connect it to your Netgear router and a wall socket.
  • Power on your Netgear WiFi router and wait for the LED to turn green.
  • Create a wired or wireless connection between your home router and the existing modem.
  • Then, open an updated web browser on your laptop.
  • Type routerlogin.net in the address bar of your web browser and press the Enter key.
  • As soon as you hit Enter, the Netgear router login web page will appear.
  • Refer to the Netgear manual and fill in the default admin details of your Netgear router.
  • Click on the Log In button.
  • Go to Settings > Admin Panel > Maintenance.
  • A dialogue box will appear prompting you to fill in your old password.
  • Fill in your old password and the new password in the given fields.
  • Click on the Apply button. Otherwise, your changes won’t get saved.

Ta-da! If you follow these instructions carefully, you’ll surely be able to change the password of your Netgear router with ease. But in case you get stuck at some point, then don’t hesitate to get in touch with our highly experienced technical experts.

If you want to fix the issue on your own, then the following troubleshooting tips might of some help to you.

Resolved: Can’t Change the Password of the Netgear Router

Mentioned below are the troubleshooting tips that’ll help you in fixing the issue at hand. If any point, you fail to understand a particular point, know that you can reach out to us at any hour of the day. Simply drop your query in the comments section below. Our experts will get back to you shortly.

  • Use the 192.168.1.254 default IP to log into your router instead of the default web address.
  • Make sure that your Netgear WiFi router is receiving a fluctuation-free power supply.
  • In case the power cable connecting your router to the wall socket is damaged, replace it.
  • Your router and modem should be properly connected. In case the Ethernet cable connecting your devices is causing trouble, why don’t you connect your devices wirelessly instead?
  • Make sure that you’ve entered the right web address while performing Netgear router login.
  • Does your Netgear WiFi router has access to a fast internet connection? No? Well, in that case, get in touch with your Internet Service Provider (ISP) right away.
  • Disable all the ad-blocking software. Now, try to log into your router to change its password.

Still no luck? Well, then waste no time in getting in touch with our highly experienced technical experts.

Continue Reading

Tech

Resolved: Netgear Extender Failed to Auto Update its Firmware

Published

on

By

To ensure proper functioning of your Netgear WiFi extender, there is a need to keep the firmware of your extender up-to-date. Your Netgear extender is intended to auto update its firmware. But sometimes, Netgear range extender fails to auto update the firmware, resulting in plethora of issues with your WiFi device.

If your Netgear extender fails to auto update its firmware, then here’s the troubleshooting guide for you. Here, we have covered various workarounds to fix “Netgear extender failed to auto update its firmware” issue in no time. Let’s get started!

Steps to Fix Netgear Extender Failed to Auto Update its Firmware Issue

Have a quick glance at the steps listed below to troubleshoot Netgear extender failed to auto update its firmware issue:

Power Cycle Your Netgear Extender

This is one of the easiest tips to fix Netgear extender failed to auto update its firmware issue. To power cycle your Netgear extender, you need to:

  • Turn off your Netgear extender. Simply unplug it from its respective wall outlet.
  • Disconnect all the devices that are connected to your Netgear extender.
  • Count to 15.
  • After that, plug your Netgear extender back in.
  • Thereafter, connect your devices with your Netgear extender using an Ethernet cable or in a wireless manner.

Now, access the default mywifiext.net web page and check if your extender has started searching for auto firmware update.

Relocate Your Netgear Extender

Always place your Netgear extender closer to your router or access point. Also, make sure that your Netgear extender is placed openly on a higher shelf. The device shouldn’t be hidden inside a cabinet or under a table. Doing so will ensure that your extender is getting enough WiFi speed to perform the firmware update process.

Check the Status of Internet Connectivity

Check your internet speed. Ensure that it is sufficient for the working of your Netgear extender. To check the internet speed, all you have to do is to open any web browser of your choice, type internet speed test and hit the Enter key. The result will be displayed on the same screen.

On the off chance if your internet speed is not as expected, then:

  • Contact your ISP and ask him to upgrade your data plan and update your WiFi device.
  • For better and extended WiFi coverage everywhere, switch to Netgear router.

Hopefully, the steps given-above fix the Netgear extender failed to auto update its firmware issue. But still, if the same issue continues to trouble you, fret not. Update the firmware on your Netgear extender manually by following the steps provided below.

How to Manually Update Netgear Extender Firmware?

  • Make sure that your Netgear extender is powered on and connected to your router’s WiFi.
  • Connect to your PC or laptop to the Netgear extender.
  • Open a web browser of your choice and visit Netgear’s official site.
  • Enter your Netgear extender’s Model Number.
  • Click on Downloads and select a firmware version for your extender.
  • Once done, click on Download and unzip the file.
  • Open a new tab, launch a new web browser window and enter mywifiext.
  • The extender login page displays.
  • Enter your extender’s username and password.
  • The Status page displays.
  • Click on Firmware Update, click on the Browse button, select the downloaded firmware file and then click on the Upload button.
  • The Netgear extender firmware update process will start. Your extender will restart once the firmware update process gets completed. The firmware update process will take a couple of minutes.

Note: You can use 192.168.1.250 IP as a URL in case the web address mywifiext doesn’t work for you.

Kudos! You have successfully updated the firmware of your Netgear extender manually.

Verdict
We recommended that you first go through the troubleshooting steps to fix Netgear extender failed to auto update its firmware issue. In the event that the troubleshooting steps given in the post do not work for you, feel free to contact or veteran technicians via comments. They will provide you quick solutions to fix the issue and perform Netgear extender setup process without any hassle.

Continue Reading

Digital Marketing

What Point to Look in a Social Media firm

Published

on

By

social media agency Dubai

If your company has a strong social presence, and if anyone can go online and create a Facebook page or post some tweets, this is not the greatest strategy to build a true clientship.
If you are looking for a social media agency Dubai and thinking about what characteristics and abilities are required for your success? We will discuss some points in this blog to assist you.

How to Find Social Media Firm

Here a few points to look for for a digital marketing company.

Their Engagement and Your Goals

The first thing that you need to identify are the social media that you want to attain. Your goals will influence your social media strategy and quantify your progress, so that your business can only profit…

The research demonstrates that organizations with a clear content strategy generate 27.1% better earnings rates and 18.1% greater quotas.

Ensure that the social media agency gets involved in everything it does. Everybody can maintain a social media account, but few can manage it and participate. Make sure you can verify your outcomes and illustrate from your experience that you and your firm can achieve the same thing.

Brand Awareness and Lead Generation

Your aim is to reach a group of new individuals through social media. You want your internet presence to expand, and you want people to discuss your brand or content. You might also work to add your figures and contribute numbers to the next one.

Furthermore, you would want to utilize social media to plan interest seeds and urge potential clients to enter a sales funnel. For example, by presenting your finest defined content as adverts, you may collect email subscribers from social media.

Customized Customer Services

It is now a normal habit for customers to access companies on social media for assistance (or complaints). Your objective may thus be to keep consumers pleased with such messages.

You may share your goals with a social media firm and development milestones in order to work together after you know what your goals are.

For all its customers, some companies adopt the same social media techniques. That’s just not working.

Every customer has its own business objectives and a distinct target audience. So, the approach of social media cannot be one-size-fits-all. You have to pick an agency that gives a customized experience that meets your requirements and objectives.

Expertise with Proven Result

In the UAE alone, there are hundreds of digital agencies. Many offer comparable services to a wide spectrum. So little wonder if all of them provide the same thing, it is tough to select between them.

Therefore, a refined degree of experience must be the differentiating feature. A large social media agency can demonstrate that it is developing high-performance campaigns. You should thus search for case studies, reports, and evaluations that demonstrate that the agency can.

Give A Proper Information

If you publish essential documents, guides, strategies, and reports, a social media firm may do more on your behalf.

In several channels, for example, you may have a stated content plan, including your blog, email, and more. The social media agency must integrate its activities with its overall strategy.

Or maybe you get a rigorous guide to brand style. Share this guidance and the company will be able for every innovative product to pick the proper tone and design components.

The aim is to make sure that the agency appears on the page as fast as possible. The proper information is shared.

Communicate in Better Way

It is also crucial to keep communications up during campaigns or project activities and not simply to express your objectives and information at the beginning of your working relationship.

All social media advertising and the content will be published on time and fulfill your criteria when you communicate properly and effectively. For example, you need to provide fresh corporate information that you want to upload in advance or approve material as scheduled. You also need to conduct the essential job.

In the whole process, communication is mostly the key. You will want a social media agency to assist you to get the necessary results, but you must empower them.

Conclusion

Before taking a decision, research and compare social media agencies. A lot of venues, besides the firm website, are where you may get essential information.

Continue Reading

Trending

Copyright © 2020 wackulus.